FAQ  •  My feedback  •  Feedback
UKLockpickers.co.uk Lockpicking supplies such as Lockpicks, tools, and more! COMMANDOLOCK.COM Military grade padlock systems lockpickshop.com A source for lockpicking supplies such as lockpicks, locksmith tools, and more!

Tokoz Tech 300

<<

least

Familiar Face

Posts: 44

Joined: Sat Apr 18, 2020 8:44 pm

Location: Czech Republic

Post Sat Sep 26, 2020 2:47 pm

Tokoz Tech 300

Although on the first sight this looks like a normal pin tumbler cylinder, it is much more interesting than that...
It is actually something between pin tumbler and wafer lock.
tokoz_tech1.jpg

The lock itself is very different from most other locks - its body seems to be cast, and the core doesn't slide to the front, but back (which might make pulling a bit harder, depending on the lock body material). Also the gutting is somewhat different - you have to punch out the two pins on the bottom (punch from the side with the little dimple), then remove the lock body, but be careful not to drop the little double cross thingy as it holds the springs and pins/wafers...

The pins/wafers seem stamped from an steel sheet and the key part holds a ball bearing, that comes in contact with the key. This not only causes less wear and tear on the lock and key, but also allows for some ridiculous bitting (not to mention the pick might slide off the pin easily). Also note the notches on the top of the drivers 2 and 4 - they act like a spool pins.

The core itself seem to be ready for passive side pins - there are both holes for them and the groove in the lock body; the lock I have didn't contain them. There are also two notches on the top of the core, of which the one closer to the center of the lock was fitted with a steel part - not sure if it is supposed work as an anti-drill measure, or if it is something else...

As far as the picking is concerned, the feel of the lock is also quite different - the center part is spring loaded, which dampens the core movement a bit. Obviously a very deep hooks seem to be needed otherwise you risk oversetting the high cut pins, but the keyway is restricted enough to make you switch to a shallower one whenever possible. Also the pin side of the core is curved enough to make tensioning there a challenge...
You do not have the required permissions to view the files attached to this post.
<<

madsamurai

User avatar

Active Member

Posts: 365

Joined: Wed Jan 04, 2017 4:13 am

Location: Germantown, Ohio

Post Sun Sep 27, 2020 4:34 pm

Re: Tokoz Tech 300

That's interesting... Seems the major advantages would be anti-torque strength in the wide pins, and they'd be harder to drill as well. Seems like they could do a lot more with anti-pick grooves and such on those long sides of the pins, rather than settling for a basic spool, but maybe there are limitations there since they're just floating.
<<

least

Familiar Face

Posts: 44

Joined: Sat Apr 18, 2020 8:44 pm

Location: Czech Republic

Post Sun Sep 27, 2020 7:01 pm

Re: Tokoz Tech 300

I was thinking about making some serrations on the side of the pin one, but I'm not sure if the pin/slider wouldn't just file through the lock core and body - the metal doesn't seem like a brass, and I'm not sure how it would hold against the (probably) stainless steel.
Kind regards,

Michal
<<

whizdumb

User avatar

Active Member

Posts: 393

Joined: Mon Oct 12, 2009 5:28 am

Location: NJ, USA

Post Mon Sep 28, 2020 3:49 pm

Re: Tokoz Tech 300

A look down that cylinder housing shows what appears to be a side-bar cut out. Does this operate with some sort of side-bar mechanism?
Image
Whizdumb81 wrote:You can't handle the DCAP
xe0 wrote:how about a peterson gov steel baseball bat so i can thwap motherfuckers
ecksdee wrote:To learn to pick locks is to learn how to speak a language spoken only in whispers and riddles.

http://www.youtube.com/user/HobbyPicker
<<

least

Familiar Face

Posts: 44

Joined: Sat Apr 18, 2020 8:44 pm

Location: Czech Republic

Post Mon Sep 28, 2020 5:57 pm

Re: Tokoz Tech 300

whizdumb wrote:A look down that cylinder housing shows what appears to be a side-bar cut out. Does this operate with some sort of side-bar mechanism?

No, there is no sidebar; the cut out is aligned with the four holes in the side of the core, so I assume there might be some passive pins fitted into this lock...

Funny thing is, that I haven't found a word about them in the manufacturer's materials, but there is a foto of a key, that has the holes on the side... Maybe they use it for the masterkeying.
Kind regards,

Michal

Return to Lock Porn

Who is online

Users browsing this forum: CommonCrawl [Bot]

Don't forget to visit our sponsors for all of your lockpicking needs!
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Grop
"CA Black" theme designed by stsoftware