Page 96 of 106

Re: What have you picked today

PostPosted: Fri Apr 13, 2018 2:52 am
by MartinHewitt
huxleypig wrote:
safecracker33 wrote:Three little Chubb 5 lever locks on bank nightsafe wallets.

Are these curtained?

Not with a tool of this type.

Re: What have you picked today

PostPosted: Sat Apr 14, 2018 8:06 am
by safecracker33
huxleypig wrote:
safecracker33 wrote:Three little Chubb 5 lever locks on bank nightsafe wallets.



Are these curtained?
No not curtained.

safecracker33 wrote:Tested a couple of homebrew picks
Function rather than beauty for me, a little butter or paint type knife, cost 50p and I gave it a try because it already had a handle fitted, and a little penknife from bangood that has made a nice little folding pocket pick that can become my keyring if I wish, Popped a couple of little Asec 5 pin roller shutter bullet locks with each of them as a test. the key one especially is surprisingly nice to hold and use :)


Were these locks prone to the bypass? Nearly every one of these shutter locks I have seen are...
Didn't try to bypass them as was just testing the picks, but would suspect so, will check them when I get the chance


Regarding Mul-T-Locks; the inner pins can only ever be +/- 1 cut away from the outer pin. Or level, of course.

Re: What have you picked today

PostPosted: Tue Apr 17, 2018 11:56 am
by brocktarblack
I picked an Abus 80TI/50 today. My first abus picked. I bypassed a couple in the past, but hey, that's too easy on the titaliums!

Re: What have you picked today

PostPosted: Wed Apr 18, 2018 3:11 pm
by greengrowlocks
After picking through my Abloy Classic locks a few weeks ago I decided to start on a different tool for the Abloy DiskLock. I finished making the tool last week and for the last few nights been trying to get it picked. Finally today I got the lock open. I found it to be harder to pick than the Classic, mostly due to the fact only limited torque can be applied to the 1.3 mm diameter shaft of the tensioner. If I could apply more torque to the tensioner I feel that identifying false vs true gates would become easier. Right now I only have this one DiskLock but in the next week should be getting a few more. While waiting for the other DiskLocks to arrive I plan to make a second tool with some improvements in design and depth/space markings on the handle of the tensioner.

Abloy DiskLock Picked
Image
Image

Abloy DiskLock Tool
Image
Image
Image

Re: What have you picked today

PostPosted: Wed Apr 18, 2018 3:40 pm
by MartinHewitt
Great! Do you have photos of the internals?

Re: What have you picked today

PostPosted: Thu Apr 19, 2018 8:24 am
by greengrowlocks
MartinHewitt wrote:Great! Do you have photos of the internals?


Yes, prior to making the tool I disassembled this lock to get a better look at how it works. The most noticeable difference between this and the Classic is the return bars which allow the lock to be opened CW or CCW. There are two tension discs or 0 cuts in the lock that rotate the return bars, once the return bars are fully rotated in either direction torque is applied to the plug. This lock also uses alternating sized spacers. The copper colored spacers are 0.59 mm and the black are 0.49mm.

Abloy DiskLock Gutted (return bars not visible, they are inside the plug.)
Image
Closeup of discs, spacer, tension disc (0 cut disc), and sidebar
Image

Return bars in DiskLock
Image
Image

Re: What have you picked today

PostPosted: Thu Apr 19, 2018 4:38 pm
by MartinHewitt
Thanks. So you need to tension both tension discs at some point? Do the code discs have to valid gates?

Re: What have you picked today

PostPosted: Fri Apr 20, 2018 10:09 am
by greengrowlocks
MartinHewitt wrote:Thanks. So you need to tension both tension discs at some point? Do the code discs have to valid gates?


All that is needed is to rotate the second tension disc with the pick while using the tensioner to tension the rear tension disc. Thankfully it's easy to identify the second disc by feel with the the pick (It's narrower in the middle than the others). Once that second tension disc is rotated you only need to apply tension to the rear disc since now that the return bars are fully rotated. I took some photos last week to illustrate what is happening to the return bars when just the rear disc is tensioned, and when the second tension disc is rotated while applying tension to the rear disc.

Tension provided to only the rear disc (return bar does not fully rotate)
Image

Tension provided to the rear disc and the second tension disc rotated with the pick (return bars fully rotate and torque is now applied to plug)
Image

Re: What have you picked today

PostPosted: Fri Apr 20, 2018 10:30 am
by MartinHewitt
Thanks!

Re: What have you picked today

PostPosted: Fri Apr 20, 2018 12:50 pm
by Patrick Star
Since today is a certain famous Austrian guy's birthday, I figured I should dig out some Austrian locks and re-pick them!
("The greatest trick the Austrians ever pulled off was to convince the world that Mozart was Austrian and that Hitler in fact was German.")

evva.png


The left one is almost too easy. With proper tool choice, the profile isn't really an obstacle at all. It does make setting the spools somewhat tricky, but they are the first two pins so even then it's not exactly hard.
The right one is a real PITA though! Really tight profile. Plus this lock is all old, worn, and dirty. Even after a good cleaning the pins really don't move smoothly. Even the plug rotation itself is all grimed up - to the point I didn't realize at first that I had actually picked it.

Re: What have you picked today

PostPosted: Sat Apr 21, 2018 5:52 pm
by GWiens2001
Honda Sidewinder ignition lock. My first 2-in-1 Lishi pick/decoder. :D

Image

Image

Image

Gordon

Re: What have you picked today

PostPosted: Sat Apr 21, 2018 9:13 pm
by jharveee
Nice going Gordon! Lishi Tools are like Potato Chips.

Re: What have you picked today

PostPosted: Sat Apr 21, 2018 9:24 pm
by GWiens2001
jharveee wrote:Nice going Gordon! Lishi Tools are like Potato Chips.


I am afraid of that. Luckily, I have an excuse for this one since I work at a Honda dealership, so can justify the cost (not too bad) for this one.

Gordon

Re: What have you picked today

PostPosted: Sun Apr 22, 2018 12:07 pm
by kilae
Not special!

Image
Image

Re: What have you picked today

PostPosted: Mon Apr 23, 2018 10:55 pm
by huxleypig
Good work on the Disclock GreenGrow! Wait until you get some with nastier warding. With Disclock you have the (relative) luxury of being able to move the discs in both directions too, so you can wiggle and get false/real gate info easier. It still takes some hard work to get the picking tip right though. Nice job.

**EDIT** In fact, you just made me remember that The Silver Bullet is good for this profile too :-) **EDIT**